313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity nlp65 series single, dual, and triple output special features ? universal input ? 3 x 5 footprint ? low profle fts 1u applications ? en61000-3-2 compliance option (hcc) ? overvoltage and short circuit protection ? 65 w with free air convection cooling ? en55022, en55011 conducted emissions level b ? en61000-4-2,-3,-4, -5, -6 immunity compliant ? rohs compliant ? lpx80 enclosure kit available ? 2 year warranty total power: 65 - 75w input voltage: 85 - 264 vac 120 - 370 vdc * # of outputs: single, dual, triple safety vde0805/en60950/iec950 file no. 1040100-3336-0096 license no. 114404 ul1950 file no. e136005 csa c22.2 no. 950 file no. lr41062c china compulsory certifcation 60950 *nlp65-76xx version only ? ? ? ? ? rev.12.12.08_102 nlp65 series 1 of 4 electrical specifcations input input voltage range: universal input (see note 2) nlp65-76xx version only 85-264 vac 120-370 vdc input frequency range: 47-63 hz input current: (cold start) 120 vac 230 vac 17 a max. 32 a max safety ground leakage current: 120 vac, 60 hz 230 vac, 50 hz 0.7 ma 1.4 ma input current: 120 vac, with pfc 230 vac, with pfc 120 vac, without pfc 230 vac, without pfc 1.4 ma 0.51 a rms 1.40 a rms 0.80 a rms input fuse: ul/iec127 s3.15 a, 250 vac in live and neutral output total regulation: (line and load) main output auxiliary outputs 2.0% 5.0% rise time: at turn-on 1.0 s, max transient response: main output 25% step at 0.1 a/s 5.0% or 250 mv max. dev., 1ms max. recovery to 1% temperature coeffcient: 0.02%/c overvoltage protection: main outputs 125%, 10% short circuit protection: cyclic operation continuous minimum output current: single and multiple (see note 6)
rev.12.12.08_102 nlp65 series 2 of 4 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 environmental specifcations all specifcations are typical at nominal input, full load at 25 c unless otherwise stated. output power (w atts) 32w 65w 75w 20 cfm forced air cooling 38w na tura l convection cooling dera ting cur ve 0c 10c 20c 30c 40c 50c 60c 70c thermal performance: operating (see derating curve) 0 c to +70 c (see notes 1, 3, 10) non-operating -40 c to +85 c 50 c - 70 c ambient, convection cooled derate to 50% load 0 c to 50 c, ambient, convection cooled 65 w 0 c to 50 c, ambient 20cfm forced air (see note 10) 75 w peak (0 c to 50 c, 60 s) see table relative humidity: non-condensing 5 to 95% rh altitude: operating 10,000 feet max. non-operating 30,000 feet max. vibration (see note 5): 5-500 hz 2.4 g rms peak shock per mil-std-810e 516.4 part iv emc charateristics (11, 12) conducted emissions: en55022, fcc part 15 level b esd air: en61000-4-2, level 3 perf. criteria 1 esd contact: en61000-4-2, level 4 perf. criteria 1 surge: en61000-4-2, level 3 perf. criteria 1 fast transients: en61000-4-4, level 3 perf. criteria 1 radiated immunity: en61000-4-3, level 3 perf. criteria 2 conducted immunity: en61000-4-6, level 3 perf. criteria 2 general specifcations hold-up time: 120 vac, 60 hz 230 vac, 50 hz 16 ms @ 65 w 78 ms @ 65 w effciency: 120 vac, 65 w 72% typical isolation voltage: input/output input/chassis 3000 vac 1500 vac switching frequency: fixed 100 khz, 5 khz approvals and standards: (see notes 9, 13) en60950, vde0805 iec950, ul1950, ccc60950 csa c22.2 no. 950 weight: 283 g (10 oz) mtbf demonstrated: mil-hdbk-217f 150,000 hours min
rev.12.12.08_102 nlp65 series of 4 embedded power for business-critical continuity 313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 1 natural convection cooling. models nlp65-x629j, nlp65-x608j, nlp65- x610j must not exceed 62.5 watts continuous output power with natural convection. model nlp65-x620j not to exceed 65 watts continuous output power with natural convection. model nlp65-3322j must not exceed 60 watts continuous output power with natural convection. 2 when the input voltage is less than 90 vac the operating temperature range is 0 c to +40 c. the ripple and regulation specifcations may not be met. 3 peak output current lasting less than 60 seconds with duty cycle less than 5%. during peak loading, output voltage may exceed total regulation limits. 4 figure is peak-to-peak for convection power rating. output noise measurements are made across a 20 mhz bandwidth using a 6 inch twisted pair, terminated with a 10 f electrolytic capacitor and a 0.1 f ceramic capacitor. 5 three orthogonal axes, random vibration 10 minutes for each axes, 2.4 g rms 5 hz to 500 hz. 6 a minimum load on the main output is required for proper start up. for multiple outputs and single +5v output, the minimum load on the +5 v is 0.2 a. for single outputs greater than +5 v the minimum load is 0.1 a. to maintain stated regulation then: for single output units i 0.2 a for multiple output units 0.25 i(a)/i(b) 5, for i(a) 0.2 a. 7 for optimum reliability, no part of the heatsink should exceed 120 o c, and no semiconductor case temperature should exceed 130 o c. 8 caution: allow a minimum of 1 second after disconnecting line power when making thermal measurements. 9 this product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. 10 maximum continuous output power for all multiple output models must not exceed 75 watts (70 watts for nlp65-3322j)with 20 cfm forced air cooling. 11 conducted emissions testing were performed using the standard en55022 set- up with a stand alone nlp65 unit placed on a grounded metal plate with a line choke on the ac input and ground wires (i.e. the wires are looped through an emi suppression toroid). for system compliance it is usually necessary to install an off-the-shelf ac inlet with an integral line flter in the system chassis or to install a line choke on the input wires as close as possible to ac entry point of the system chasssis. please contact the applications group for assistance with emi compliance. 12 the nlp65 units with the suffx g is the ground pin and ground choke option. j2, l6 and jp10 are included. j2 is a safety agency approved grounding pin, l6 is a ground choke and jp10 is a jumper. this option is intended for use in non- metallic chassis applications where grounding is not possible via the mounting screws. the ground choke is provided to assist system emc compliance. when performing conducted emissions testing on stand alone units, the g option is required to meet level b. to order simply add the suffx g to the standard model number, e.g. NLP65-7608Gj, nlp65-9608gj. this option is available for both the pfc and non-pfc versions. 13 all models require a minimum mounting stand-off of 0.25 inches (6.35 mm) in the end use product. 14 the nlp65-9608j is available with an enclosure. to order an enclosed version, see model numbering options below. 15 no pfc version, en61000-3-2 is not applicable to this model. 16 the j suffx indicates that these parts are pb-free (rohs 6/6) compliant. 17 notice: some models do not support all options. please contact your local emerson network power representative or use the on-line model number search tool at http://www.powerconversion.com. model numbering options 1 the enclosure version includes: iec connector, on/off switch, wire harness output connector and ftted cover. to order, please add the suffx e the model number, e.g. nlp65-9608ej. see nlp65 enclosure for details. 2 a safety earth ground pin and ground choke are available as an option. to order, please add the suffx g the model number, e.g. nlp65-x608gj. 3 to order an enclosure kit (unftted), order the part number lpx80. output voltage output current ripple (4) total regulation (6) non-harmonic corrected harmonic corrected ground pin (12, 14, 17) max (1) peak (3) fan (10) +5 v (ia) 7.5 a 9.1 a 8 a 50 mv 2.0% nlp65-7608j nlp65-9608j nlp65-x608gj +12 v (ib) 2.5 a 3.3 a 3 a 150 mv 5.0% C12 v 0.65 a 0.81 a 0.8 a 120 mv 5.0% +5 v (ia) 7.5 a 9.1 a 8 a 50 mv 2.0% nlp65-7610j nlp65-9610j nlp65-x610gj +15 v (ib) 2.2 a 2.9 a 2.5 a 150 mv 5.0% C15 v 0.65 a 0.85 a 0.8 a 150 mv 5.0% +5 v 7.0 a 9.1 a 8.0 a 50 mv 2.0% nlp65-3322j (15) +24 v 1.5 a 2.6 a 2.0 a 240 mv 5.0% +12 v 0.7 a 1.0 a 1.0 a 120 mv 5.0% +5 v (ia) 7 a 9.1 a 8 a 50 mv 2.0% nlp65-7620j nlp65-9620j nlp65-x620gj +24 v (ib) 2 a 2.6 a 2 a 240 mv 5.0% +5 v (ia) 7 a 9.1 a 8 a 50 mv 2.0% nlp65-7629j nlp65-9629j nlp65-x629gj +12 v (ib) 2.5 a 3.3 a 3 a 150 mv 5.0% +5 v 10 a 13 a 12 a 50 mv 2.0% nlp65-7605j nlp65-9605j nlp65-x605gj +12 v 5.4 a 7 a 6.5 a 120 mv 2.0% nlp65-7612j nlp65-9612j nlp65-x612gj +15 v 4.4 a 5.7 a 5.3 a 150 mv 2.0% nlp65-7615j nlp65-9615j nlp65-x615gj +24 v 2.7 a 3.5 a 3.5 a 240 mv 2.0% nlp65-7624j nlp65-9624j nlp65-x624gj notes
313 process yellow 3405 1797 1375 116 2607 652 242 2985 375 240 embedded power for business-critical continuity rev.12.12.08_102 nlp65 series 4 of 4 c19 all dimensions in inches (mm) 5.00 (127.00) maximum component height 1.26 (32.00) n 1 l j3 j1 j2 6 4.550 (1 15.57) 2.550 (64.770) to lerance: .xxx 0.005" .xx 0.02" 0.225 (5.715) 3.00 (76.20) 3 mounting hole diameter 0.156 (4.00) t1 1 mechanical drawing americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower@ emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. emersonnetworkpower.com embedded computing embedded power monitoring outside plant power switching & controls precision cooling racks & integrated cabinets services surge protection emerson network power. the global leader in enabling business-critical continuity. ac power connectivity dc power pin connections j1 pin 1 ac line pin 2 no pin pin 3 ac neutral j2 (on g suffic only) pin 1 safety ground output pin connections j3 single dual triple pin 1 v (a) v (b) v (b) pin 2 v (a) v (a) v (a) pin 3 v (a) v (a) v (a) pin 4 return return return pin 5 return return return pin 6 return n/c v (c) input and output connectors mating connectors ac (j1) molex 26-60-4030 type molex 09-50-3031 or equivalent with molex 08-50-0105 or equivalent crimp terminals dc (j3) molex 26-60-4060 molex 09-50-3061 with molex 2478 phos - phor bronze crimp terminals or equivalent. note: the input and output connectors are the same as those used on nfs40, nfn40, nal40, nan40 and nlp40.
|
